CIS: Plastic Cutting Machine Market 2020

Plastic Cutting Machine Market Size in CIS

The revenue of the plastic cutting machine market in CIS amounted to $X in 2017, jumping by X% against the previous year. The market value increased an average annual rate of +X% from 2007 to 2017; however, the trend pattern indicated some noticeable fluctuations throughout the analyzed period. The most prominent rate of growth was recorded in 2008, when market value increased by X% y-o-y. The level of plastic cutting machine consumption peaked of $X in 2013; however, from 2014 to 2017, it stood at a somewhat lower level.

Plastic Cutting Machine Production in CIS

In 2017, the amount of cutting, splitting and peeling machines for working rubber or plastics produced in CIS amounted to X units, increasing by X% against the previous year. The total output volume increased an average annual rate of +X% over the period from 2007 to 2017; the trend pattern remained consistent, with only minor fluctuations being recorded in certain years. The growth pace was the most rapid in 2017, when it surged by X% against the previous year. In that year, the plastic cutting machine production attained their peak volume, and is likely to continue its growth in the immediate term.

Plastic Cutting Machine Exports in CIS

In 2017, exports of cutting, splitting and peeling machines for working rubber or plastics in CIS stood at X units, waning by -X% against the previous year. The plastic cutting machine exports continue to indicate a significant deduction. The most prominent rate of growth was recorded in 2012, when it surged by X% y-o-y. In that year, the plastic cutting machine exports attained their peak volume of X units. From 2013 to 2017, growth of the plastic cutting machine exports stood at a somewhat lower level.

In value terms, plastic cutting machine exports totaled $X in 2017. The plastic cutting machine exports continue to indicate a perceptible shrinkage. In that year, the plastic cutting machine exports attained their peak level of $X. From 2013 to 2017, growth of the plastic cutting machine exports failed to regain its momentum.

Plastic Cutting Machine Exports by Country in CIS

Belarus represented the key exporting country with an export of around X units, which finished at X% of total exports. It was distantly followed by Russia (X units), comprising X% share of total exports. Moldova (X units) followed a long way behind the leaders.

Belarus experienced a relatively flat trend pattern of cutting, splitting and peeling machines for working rubber or plastics exports. At the same time, Moldova (+X%) displayed positive paces of growth. Moreover, Moldova emerged as the fastest growing exporter in CIS, with a CAGR of +X% from 2007-2017. By contrast, Russia (-X%) illustrated a downward trend over the same period. While the share of Russia (X%) increased significantly in terms of the global exports from 2007-2017, the share of Belarus (-X%) displayed negative dynamics. The shares of the other countries remained relatively stable throughout the analyzed period.

In value terms, Belarus ($X), Russia ($X) and Moldova ($X) were the countries with the highest levels of exports in 2017, together accounting for X% of total exports.

Moldova (+X% per year) recorded the highest growth rate of exports, among the main exporting countries over the last decade, while the other leaders experienced mixed trends in the exports figures.

Plastic Cutting Machine Export Prices by Country in CIS

In 2017, the plastic cutting machine export price in CIS amounted to $X thousand per unit, surging by X% against the previous year. The plastic cutting machine export price continues to indicate a relatively flat trend pattern. The most prominent rate of growth was recorded in 2008, an increase of X% year-to-year. In that year, the export prices for cutting, splitting and peeling machines for working rubber or plastics reached their peak level of $X thousand per unit. From 2009 to 2017, growth of the export prices for cutting, splitting and peeling machines for working rubber or plastics stood at a somewhat lower level.

Export prices varied noticeably by the country of destination; the country with the highest export price was Russia ($X thousand per unit), while Belarus ($X thousand per unit) was amongst the lowest.

From 2007 to 2017, the most notable rate of growth in terms of export prices was attained by Belarus (+X% per year), while the other leaders experienced more modest paces of growth.

Plastic Cutting Machine Imports in CIS

In 2017, approx. X units of cutting, splitting and peeling machines for working rubber or plastics were imported in CIS; approximately reflecting the previous year. The plastic cutting machine imports continue to indicate a measured drop. The pace of growth was the most pronounced in 2011, when it surged by X% year-to-year. Over the period under review, the plastic cutting machine imports reached its maximum volume of X units in 2012; however, from 2013 to 2017, it failed to regain its momentum.

In value terms, plastic cutting machine imports amounted to $X in 2017. The plastic cutting machine imports continue to indicate a deep slump. The level of imports peaked of $X in 2012; however, from 2013 to 2017, it stood at a somewhat lower level.

Plastic Cutting Machine Imports by Country in CIS

In 2017, Russia (X units) represented the key importer for cutting, splitting and peeling machines for working rubber or plastics, achieving X% of total imports. Kazakhstan (X units) occupied a X% share (based on tons) of total imports, which put it in second place, followed by Azerbaijan (X%). Belarus (X units) occupied the minor share of total imports.

Imports into Russia decreased at an average annual rate of -X% from 2007 to 2017. Azerbaijan experienced a relatively flat trend pattern. Kazakhstan (-X%) and Belarus (-X%) illustrated a downward trend over the same period. Kazakhstan (X%) and Russia (X%) significantly strengthened its position in terms of the global imports, while the shares of the other countries remained relatively stable throughout the analyzed period.

In value terms, Russia ($X) constitutes the largest market for imported cutting, splitting and peeling machines for working rubber or plastics in CIS, making up X% of global imports. The second position in the ranking was occupied by Belarus ($X), with a X% share of global imports. It was followed by Kazakhstan, with a X% share.

From 2007 to 2017, the average annual rate of growth in terms of value in Russia totaled -X%. In the other countries, the average annual rates were as follows: Belarus (-X% per year) and Kazakhstan (-X% per year).

Plastic Cutting Machine Import Prices by Country in CIS

The plastic cutting machine import price in CIS stood at $X thousand per unit in 2017, rising by X% against the previous year. The plastic cutting machine import price continues to indicate a deep contraction. The pace of growth appeared the most rapid in 2017, when it surged by X% year-to-year. Over the period under review, the import prices for cutting, splitting and peeling machines for working rubber or plastics attained its peak figure level of $X thousand per unit in 2007; however, from 2008 to 2017, it stood at a somewhat lower level.

There were significant differences in the average import prices amongst the major importing countries. In 2017, the country with the highest import price was Belarus ($X thousand per unit), while Azerbaijan ($X thousand per unit) was amongst the lowest.

From 2007 to 2017, the most notable rate of growth in terms of import prices was attained by Belarus (-X% per year), while the other leaders experienced a decline in the import price figures.

Source: IndexBox Platform